We checked out all of the reviews, and put together a list of the best sellers. Check out the top 3d Printer Board below.
No. 1
BIGTREETECH SKR Pro v1.2 32-bit Motherboard high-Frequency 3D Printer Control Board, Support TMC5160, TMC2208, TMC2130,...
- The main control uses the ARM-level Cortex-M4 series with a 32-bit dominant frequency of 168 MHz STM32F407ZGT6 chip, performance is greatly...
- Equipped with highly modular open source firmware Marlin2.0, it is convenient for users to DIY and further-development, to avoid the worry...
- Motor driver support :TMC5160,TMC2208,TMC2130,ST820,LV8729, DRV8825,A4988, etc.Display screen support: BIGTREETECH- 2.8 inch...
- Support Serial WIFI Online Printing. 6 motor drives, 3 extruders, 3 CNC fans. Reserve extended ports of BL Touch, PWM, ADC, UART, I2C and...
No. 2
WOWOONE CNC 3D Printer Kit for Arduino Mega 2560 R3 RAMPS 1.4 Controller LCD 2004 + 6X Limit Switch Endstop 5 A4988...
- 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module.
- The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.
- It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors.
- Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors
- This shield can make quick work for managing stepper motors in your project
No. 3
Creality Ender 3 New Upgraded Motherboard Silent Mainboard V4.2.7 with TMC2225 Driver Marlin 2.0.1 for Ender 3/ Ender 3...
- Silent function( Customized and Non-standard matching)! Creality upgraded V4.2.7 silent board has been updated from 8 bit to 32 bit.
- Driver - TMC2225 driver & Creality V0.0.6 firmware ( based on Marlin 2.0.1) and bootloader preinstalled. You can copy the firmware file to a...
- Thermal runaway protection is enabled. The Board is Optimized by Circuit, effectively solve the Heating Problem.
- Easy to Operate: With USB Port,can be Worked With E/Z/Y/X Axis Motor.
No. 4
BIGTREETECH SKR Mini E3 V2.0 Control Board 32Bit New Upgrade for Creality Ender 3, with TFT35 E3 V3.0 Graphic Smart...
- 【TFT35 E3 V3.0】 ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz; Upgrade the firmware by SD card. It is easy and...
- 【SKR Mini E3 V2.0】 ARM Cortex-M3 Series STM32F103RCT6 Master Controller with 32-bit Main Frequency of 72MHz Chip;Integrate UART mode of...
- 【TFT35 E3 V3.0】 This display board has higher compatibility. Users can select two work modes:UART serial port screen mode and 12864...
- 【TFT35 E3 V3.0】 LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD...
- 【SKR Mini E3 V2.0 Firmware】 https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V2.0 ；【TFT35 E3 V3.0...
No. 5
BIGTREETECH Direct SKR V1.4 Turbo Silent Mainboard + TFT35 V3.0 Touch Screen + 5pcs TMC2209 V1.2 Stepper Motor Driver 3D...
- ※1.【What Will You Get?】SKR V1.4 Turbo+TFT35 V3.0+5pcs TMC2209 V1.2 3D Printer Controller Kit
- ※2.【SKR V1.4 Turbo】Support Resume Printing While Power Off, Filament Break Detection, Automatic Shutdown After Printing and so on；...
- ※4.【 Question】: TFT "No Printer attached!",【Answer】It may be a firmware configuration or wiring problem; it may be a problem with...
- ※5.【 Question】Q:What if I received a product which looks like used?What's going on?【A】: Amazon has a return service. Some buyers...
- ※6.【TFT35 V3.0】 Upgrade the firmware by SD card. It is easy and convenient to operate. 6.【TFT35 V3.0】LCD12864 mode uses EXP1, EXP2...
No. 6
KINGPRINT 3D Printer MKS Gen V1.4 Controller Board Mega 2560 R3 Motherboard RepRap Ramps1.4 Compatible with USB
- Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.
- Replace the motor drive, drive and support A4988 DRV8825 TMC2208 TMC2130 drive.
- The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
- Using high-quality MOSFET, and better heat dissipation.
- Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.
No. 7
BIGTREETECH Direct SKR V1.4 Turbo + TFT35 V3.0 Touch Screen 3D Printer Board 32 Bit Update SKR V1.3 SKR V1.4 3D Printer...
- 1）【SKR V1.4 Turbo】Using 32-bit main frequency 120MHz ARM level Cortex-M3 series LPC1769 main control chip, the performance has been...
- 2）【SKR V1.4 Turbo】The SPI and UART working mode driven by the TMC driver, also having the DIAG pin, which eliminates complex wiring...
- 3）【SKR V1.4 Turbo】Motor driver: Support TMC5161、TMC5160、TMC2209、TMC2225、TMC2208、TMC2130、ST820、LV8729、DRV8825、A4988...
- 4）【Q】What if I received a product which looks like used?What's going on?【A】: Amazon has a return service. Some buyers have already...
- 5）【TFT35 V3.0】: LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard, EXP3 is the LCD...
No. 8
BIGTREETECH PT100 Temperature Sensor Module 3D Accessories for SKR V1.3 SKR V1.4 Turbo Control Board Ender 3 V2 Ender 5...
- ❤ small size and easy to install
- ❤ The thermocouple adopts screw terminals Blocks connector.
- ❤ High precision, stable performance, stable temperature display.
- ❤ Note:The module uses 5V power supply.
- ❤ Attention:Signal need to directly connect to the pin of MCU which has ADC without any pull-up or pull-down resistors.If there is pull-up...